Digital Link DL600E E1 Guía de usuario Pagina 29
- Pagina / 140
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
2-1
2
Installation 2
This chapter describes installing the Solo E1 DSU Standalone and module:
¥ ÒPre-Installation ChecksÓ on page 2-1 (apply to both the Solo E1 DSU
and module)
¥ ÒTerminal and DIP Switch ModeÓ on page 2-2
¥ ÒCable RequirementsÓ on page 2-2
¥ ÒInstalling the Solo E1 DSU StandaloneÓ on page 2-3
¥ ÒInstalling The Solo E1 DSU ModuleÓ on page 2-17
Pre-Installation Checks
Before installing the Solo E1 DSU or module, check the shipping
package(s) and prepare the network information and the installation site.
Check the Package(s)
¥ Unpack and inspect the Solo E1 DSU for damage that may have
occurred during shipment.
¥ Save all enclosed packing slips and documents. Save shipping cartons
and packing materials until you have completed the installation and
veriÞed device operation.
¥ Verify that all equipment ordered matches the packing slip. If the
equipment does not match your order, contact Digital Link Customer
Support.
¥ Fill out and mail the registration card.
Prepare Network Information
Request the following information from your network administrator before
you install the Solo E1 DSU:
¥ Solo E1 DSU IP addressÑTo enable a Telnet connection to the Solo E1
DSU from a remote terminal.
¥ To use SNMP network management, one to three NMS IP addresses in
addition to the above IP address. These addresses are where the Solo E1
will send traps.
- Solo E1 DSU User 1
- Disclaimer 3
- ISO Compliance 3
- Table of Contents 5
- Chapter 3, ConÞguration 3-1 6
- Chapter 4, Maintenance 4-1 7
- Chapter 5, Diagnostics 5-1 8
- Table of Contents ix 9
- List of Figures 11
- List of Figures xiii 13
- List of Tables 15
- List of Tables xvii 17
- Audience 19
- Organization 19
- Conventions 20
- Typography 21
- Returning a Unit 22
- Send Us Your Comments 22
- Preface xxiii 23
- Introduction 1 25
- Service Features 26
- Management Capabilities 27
- Installation 2 29
- Terminal and DIP Switch Mode 30
- Cable Requirements 30
- Installing on a Flat Surface 31
- Installing on a Tray 32
- Installation 2-5 33
- OFF (Figure 2-2) 34
- DIP switches 34
- DIP switches for S1 and S2 35
- Installation 2-9 37
- Grounding the Solo E1 DSU 39
- Cable Connections 40
- Network BNCs 41
- Connect a Modem 43
- DE-9 Connector, Pin 8 44
- Installation 2-17 45
- Installing the Module 46
- Installation 2-19 47
- Item Status Description 48
- ConÞguration 3 51
- Log On from a Terminal 52
- Log On Through Telnet 52
- Access Rights 53
- Using The Terminal Interface 55
- Setting a Parameter 56
- Configuration 3-7 57
- Setting Unit ID 58
- Setting Date or Time 59
- Configuring Network Parameters 59
- Configuring the DATA Port 61
- Allocating Timeslots 62
- to choose 63
- Menu-0 SNMP Configuration 65
- Menu-7 Alarm I Conditions 67
- Figure 3-8 Menu-8 Alarm II 70
- (Default) Setting Description 71
- Configuration 3-23 73
- Modem Initialization Strings 74
- Configuration 3-25 75
- Maintenance 4 77
- Menu-1 Main Status 78
- Unit Status 79
- Network Status 80
- Error Statistics 81
- DATA Status 82
- Maintenance 4-7 83
- Parameter Description 85
- Event Log 87
- (Default) Events 88
- Diagnostics 5 91
- Shortcut 92
- Parameter Value Description 93
- Shortcut Test Options 93
- Self Test 94
- Error Code Description 95
- The Loop DTE Test 96
- The Loop NET Test 97
- The Loop Payload Test 97
- The DTE/NET Test 98
- The Loopup/Down Remote Tests 99
- Pattern Tests 100
- The Send 1:2 Test 101
- The Lamp Test 101
- Status LEDs 102
- The Pattern Tests 103
- Pattern Test Description 104
- Troubleshooting 6 105
- Troubleshooting 6-3 107
- The NET LED is Constantly Red 108
- Troubleshooting 6-5 109
- No LEDs Illuminate 110
- Technical SpeciÞcations A 111
- Regulatory 112
- Technical Specifications A-3 113
- Diagnostics 114
- Telnet and SNMP Management 114
- Related Model Numbers 115
- Communications 116
- Cables Cable to terminal 116
- Model Number Description 116
- Connector and Pin 117
- Assignments 117
- DATA port can 118
- DTE side connection only 119
- V.35 DB-25 121
- RS-449 DB-25 121
- Pin Signal Description 122
- Parameter 123
- (Default) Option 123
- DE-9 DB-25 123
- Factory Default ConÞgurationC 125
- COMM Port and Terminal 126
- Item Default Item Default 126
- ConÞguration Worksheet D 127
- Item Setting Item Setting 128
- Software Download E 129
- Setting Up for TFTP 130
- Initiating TFTP 131
- Setting Up for XMODEM 132
- (as instructed in the 132
- Group Field Description 133
- Abnormal Termination 134
- Error Indicators 135
- Download Aborted by User 136
- Index I-3 139
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales