Digital Link DL600E E1 Guía de usuario Pagina 74
- Pagina / 140
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
3-24 Solo E1 DSU User Guide—June 1998
3
Modem Initialization Strings
To initiate a modem connection, the Solo E1 DSU sends +++ followed by
the Þrst modem initialization string. The Solo E1 DSU waits for the modem
response. The Solo E1 DSU waits for modem response so that it can guard
against the possibility of losing the characters right after the modem reset
command. After receiving the modem response, the Solo E1 DSU sends the
second initialization string (if programmed).
Figure 3-11 shows the Menu-8 Alarm II.
DLC IBC Link Loss Alarm
(Enabled)
Enabled
Disabled
When enabled, an alarm alerts loss of IBC.
Dial Out Time Interval
(0 min.)
0 to 255
minutes
Use to extend time interval before modem dials out.
NOTE: The Solo E1 DSU assumes that the modem always sends a
response; do not program the modem to override the response.
Table 3-8 Menu-8 Alarm II Parameters (Continued)
Parameter
(Default) Settings Description
- Solo E1 DSU User 1
- Disclaimer 3
- ISO Compliance 3
- Table of Contents 5
- Chapter 3, ConÞguration 3-1 6
- Chapter 4, Maintenance 4-1 7
- Chapter 5, Diagnostics 5-1 8
- Table of Contents ix 9
- List of Figures 11
- List of Figures xiii 13
- List of Tables 15
- List of Tables xvii 17
- Audience 19
- Organization 19
- Conventions 20
- Typography 21
- Returning a Unit 22
- Send Us Your Comments 22
- Preface xxiii 23
- Introduction 1 25
- Service Features 26
- Management Capabilities 27
- Installation 2 29
- Terminal and DIP Switch Mode 30
- Cable Requirements 30
- Installing on a Flat Surface 31
- Installing on a Tray 32
- Installation 2-5 33
- OFF (Figure 2-2) 34
- DIP switches 34
- DIP switches for S1 and S2 35
- Installation 2-9 37
- Grounding the Solo E1 DSU 39
- Cable Connections 40
- Network BNCs 41
- Connect a Modem 43
- DE-9 Connector, Pin 8 44
- Installation 2-17 45
- Installing the Module 46
- Installation 2-19 47
- Item Status Description 48
- ConÞguration 3 51
- Log On from a Terminal 52
- Log On Through Telnet 52
- Access Rights 53
- Using The Terminal Interface 55
- Setting a Parameter 56
- Configuration 3-7 57
- Setting Unit ID 58
- Setting Date or Time 59
- Configuring Network Parameters 59
- Configuring the DATA Port 61
- Allocating Timeslots 62
- to choose 63
- Menu-0 SNMP Configuration 65
- Menu-7 Alarm I Conditions 67
- Figure 3-8 Menu-8 Alarm II 70
- (Default) Setting Description 71
- Configuration 3-23 73
- Modem Initialization Strings 74
- Configuration 3-25 75
- Maintenance 4 77
- Menu-1 Main Status 78
- Unit Status 79
- Network Status 80
- Error Statistics 81
- DATA Status 82
- Maintenance 4-7 83
- Parameter Description 85
- Event Log 87
- (Default) Events 88
- Diagnostics 5 91
- Shortcut 92
- Parameter Value Description 93
- Shortcut Test Options 93
- Self Test 94
- Error Code Description 95
- The Loop DTE Test 96
- The Loop NET Test 97
- The Loop Payload Test 97
- The DTE/NET Test 98
- The Loopup/Down Remote Tests 99
- Pattern Tests 100
- The Send 1:2 Test 101
- The Lamp Test 101
- Status LEDs 102
- The Pattern Tests 103
- Pattern Test Description 104
- Troubleshooting 6 105
- Troubleshooting 6-3 107
- The NET LED is Constantly Red 108
- Troubleshooting 6-5 109
- No LEDs Illuminate 110
- Technical SpeciÞcations A 111
- Regulatory 112
- Technical Specifications A-3 113
- Diagnostics 114
- Telnet and SNMP Management 114
- Related Model Numbers 115
- Communications 116
- Cables Cable to terminal 116
- Model Number Description 116
- Connector and Pin 117
- Assignments 117
- DATA port can 118
- DTE side connection only 119
- V.35 DB-25 121
- RS-449 DB-25 121
- Pin Signal Description 122
- Parameter 123
- (Default) Option 123
- DE-9 DB-25 123
- Factory Default ConÞgurationC 125
- COMM Port and Terminal 126
- Item Default Item Default 126
- ConÞguration Worksheet D 127
- Item Setting Item Setting 128
- Software Download E 129
- Setting Up for TFTP 130
- Initiating TFTP 131
- Setting Up for XMODEM 132
- (as instructed in the 132
- Group Field Description 133
- Abnormal Termination 134
- Error Indicators 135
- Download Aborted by User 136
- Index I-3 139
© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales